THOR is the top-of-the-line loudspeakerkit from SEAS. It is a full range, floor-standing system that provides
the very highest level of acoustic performance. This kit uses two W18E001 woofers and a single T25CF002 "MILLENNIUM" tweeter mounted in a D'Appolito configuration.

The enclosure uses a newly developed transmission line configuration, derived both from sophisticated computer modeling, and extensive experimentation.

The line is tapered, and filled with Dacron stuffing. The two W18E001 woofers excite the line at slightly different points, smoothing the response and increasing the range of bass output.

The transmission line produces 4 dB of bass lift from 20Hz to 110HZ, with less than 1 dB of ripple. The -3dB point is 45Hz, with roll off of 12dB per octave below 45Hz.
Usable in-room bass response extends well into the low 30Hz range.

The crossover network is conventional except for a parallel circuit which supresses the response peak due to the magnesium cone.
The crossover frequency is 2.5kHz.

THOR was designed by Dr. Joseph D'Appolito, who is world-renowned for his pioneering work on MTM-based loudspeaker configurations.
He offers the following comments on THOR:

"Transmission Line loudspeakers have long enjoyed a small, but dedicated following. The advantages of TL's are well known. They are essentially
non-resonant enclosures, producing a deep, well-controlled bass response. For a given driver, bass response will extend well below that produced
with either a vented or sealed enclosure using the same driver. Above a few hundred Hz, the line filling material completely absorbs the driver backwave, giving the TL an open, non-boxy sound."

Printable PDF files:

    pdf Cabinet drawings
    pdf Cabinet drawings in inches
    pdf Crossover schematics
    pdf Measurements







*IEC 268-5 SEAS reserves the right to change technical data 

Hints to build Thor

Stuffing: For the damping of Thor, we recommend using a Dacron fibre mat weighing 360 g /sq. metre (1,2 oz / sq. Ft)
400 g (14 oz) of the damping material should be placed in the front channel; 250 g (9 oz) in the rear.

For more in-depth information about the design, please see the article by Dr. Joseph D'Appolito and Dennis Colin in AudioXpress.



DIY Kits

  • IDUNN +

    Download Idunn plans Download DSP file for Hypex AS2.100 Named Read More
  • MIMIR +

    Download Mimir plans Named after Mimir , a primal god of Read More
  • THOR +

    THOR is the top-of-the-line loudspeakerkit from SEAS. It is a Read More
  • ODIN MK3 +

      The Odin Mk3 is a completely redesigned version of Read More
  • TRYM +

      The Trym is a 2 way, 2 driver loudspeaker Read More
  • FROY MK3 +

      The FROY Mk3 is a new and improved version Read More

    Download Bifrost PDF Download Cabinet Drawings Download Cabinet Parts Bifrost Read More

    Download Delling cabinet drawings Download Delling cabinet parts list Download Read More
  • SEAS A26 Kit +

    Download SEAS A26 plans Download SEAS A26 Application Note The Read More
  • SEAS KingRO4Y Mk II +

    Download SEAS KingRO4Y plans Download SEAS KingRO4Y Application Note Download Read More
  • BRAGI +

    Download Bragi plansDownload Bragi Application Note Named after Bragi, the Read More
  • SEAS Loki MkIII +

     Download Loki MkIII plans  Download Loki MkIII Application Note  Download Read More
  • SEAS KingRO4Y Mk III +

    Download SEAS KingRO4Y plans Download SEAS KingRO4Y Application Note & Assembly Read More
  • SEAS JOY +

    Download SEAS JOY Application Note and plan The SEAS Joy speaker Read More

    Download SEAS Locus note and plan A High Performance loudspeaker featuring Read More

    Download SEAS Jollity note and plan A coaxial driver for compact Read More

    Download SEAS ACUITY note and plan A High Performance loudspeaker system Read More

    Download SEAS LUCID note and plan Download SEAS LUCID files Read More

    Download SEAS Aphel note and plan Download SEAS APHEL files Read More
  • 1